draining your waterbeds

!±8± draining your waterbeds

Draining your water mattress

draining your waterbeds

Treadmill Vs Ellipticals Fast Locking Gun Cabinets Buy Now

Waterbed Drain - How to Drain a Waterbed

!±8± Waterbed Drain - How to Drain a Waterbed

Waterbed drains and pumps are now available to make the job of filling and draining your bed much easier. Water beds offer much better body support than regular mattresses, but are usually much less convenient to deal with, especially regarding setting it up or transferring it to a new location.

This is especially true for hard side beds, which are water mattresses placed inside a strong wooden surround for support. This type of bed requires special bed frames if you wish to use one, although they can also stand on their own. The wooden support also usually makes the whole setup quite unwieldy to transport and move around. This hard side design is the original one, used originally for medical purposes, with patients who require good body support as well as those who are bedridden.

Easier to deal with is the soft side water bed type. Soft side mattresses have foam edgings instead of using a wooden surround for support. These foam sidings provide just as much support, and can still allow the soft side bed to stand on its own. A newer version of the soft side mattress is even easier to fit into existing bed frames: the foam edging has been divided into two, a lower fixed part and a top hinged foam rail.

To fill or drain a new waterbed, a fill and drain kit is usually required. This kit is often provided with the bed itself, and if not, they are readily available at furniture and home furnishing stores. One thing to remember is to turn off and unplug the heater before filling (or draining) the mattress. Then connect your bed's valve with the faucet using a garden hose (flush it out if it's been stored outside) and the faucet connector usually provided with the bed. A waterbed hose connector is attached to the end of the garden hose that goes into the valve.

Use towels to wrap around possible leakage areas and prevent any spills. When filling your bed, pour the waterbed conditioner in first before filling it with mildly warm water, about a quarter or half inch from the top of the bed supports. After shutting the water off and removing the hose, remove any air bubbles from inside the mattress by pressing on it with a broom or yardstick, toward the valve.

Draining follows a similar procedure: attach the hose to the faucet and the bed, then run the water until the hose is filled. Remove the hose from the faucet and place that end on the ground or a sink, tub, etc. Make sure that the output end of the hose is lower than the bed, and gravity will do all the work. You can go and do other things while waiting, to come back to an empty water bed.

It is only in cases where this is not possible, or if a faster drain is desired, that waterbed drains are used. Beds in basements, for instance, might be difficult to drain without using a pump. And pumps will be able to drain the mattress much faster than just siphoning the water away naturally using gravity.

Waterbed Drain - How to Drain a Waterbed

Polaris Sportsman Bumpers Coupon Organic Infant Formulas Get It Now! Indian Remy Weave This Instant

Waterbed Repair and Maintenance - What You Need to Know

!±8± Waterbed Repair and Maintenance - What You Need to Know

Owning a waterbed requires the occasional waterbed repair once in awhile. In order to keep your bed in good condition, proper maintenance and care should be taken. How do you properly maintain a waterbed?

One of the first things you need to consider is the water level in your mattress. Always remember that the water will be displaced when one person or more uses the bed. Thus, fill the water system of the mattress to just below the level of the surrounding frame and allow some roof for displacement.

When a waterbed has already been filled with water by others, it's always wise to check for air bubbles in the mattress. Just make sure that the air in the mattress is vented out through the valve. A waterbed that is free of air is quiet. So, once in awhile, you need to manually vent out the air from your mattress.

Setting your waterbed's temperature is also important to guarantee a good night's sleep. However, each person has his preference when it comes to temperature. Generally, a temperature of 28 degrees Celsius or the normal body temperature is the most typical setting for most mattresses.

A waterbed may be free from bed bugs and dust mites but the water inside the mattress might not be free from bacteria. Thus, to prevent formation of algae in the water, waterbed owners are advised to add a conditioner in the water at least every six months. The waterbed conditioner will not only purify the water and prevent bacteria, but it will also protect the surface of the vinyl mattress.

Aside from conditioners, it is also necessary to clean the vinyl surface using a special waterbed vinyl cleaner. Most mattresses have removable covers which can be slid off for easier cleaning. Some vinyl cleaners can be wiped directly on the vinyl while other vinyl cleaners need to be added water or moist before application.

If you're a waterbed owner, never forget to ensure that the safety liner of your bed is correctly in place because the safety liner will protect your room in case the water bed leaks. The liner will ensure that if the mattress gets a leak the water displaced will be contained inside the liner. It is wise to examine your waterbed mattress and the safety liner at least twice a year.

When a waterbed leaks, some people would immediately try to drain all the water from the bed. But this is actually a bigger job than repairing the vinyl itself. In case of leaks, the first you need to do is try to find where leak is coming from. Use a towel to dry off the water between the liner and the bed. Remember that the water is trapped between the liner and the mattress but you can dry it off without draining the entire bed.

A waterbed leak will usually come from the sides, top, or corners of the vinyl. Once you've found the leak, place a pillow under the safety liner to lift the mattress so that you can begin with the repair. First, dry off the punctured area and use the waterbed patch kit that is usually included in your package when purchasing the bed. Simply cut a patch of vinyl that is at least 1cm larger than the hole and use the waterbed repair adhesive to put it in place. The glue dries off very quickly and once it's dried, the mattress is ready for use. However, double check that you have completely dried off the leak between the safety line and the mattress as the spilled water will acquire algae and odor.

Waterbed Repair and Maintenance - What You Need to Know

Saved Old Schwinn Exercise Bike Rocketfish Hdmi Switch Best Saving Uniden Dct7585